BassnMan.com

Fresh Water Fishing Tips and Techniques with an Empahsis on Bass

  • Home
  • Fishing Tips
  • Fishing Techniques
  • Fishing Stories
  • Fishing Gear
  • Fishing Humor
  • Boating
  • Vehicle Tips
  • The “ZEN” Zone
You are here: Home / Fishing Gear / Upgrading the Drag and Servicing an Abu Revo

Upgrading the Drag and Servicing an Abu Revo

Today I thought I would explain how to upgrade the drag with Smoooooth Drag Carbontex replacement drag washers on a Abu Revo reel and seeing how I’ll be tearing it down I figured I might as well service it at the same time. This video is on the Skeet Reese Revo which was very popular awhile back but I’m sure the other Revo’s will basically be the same.

I use Cals Reel Grease, normally I prefer Lightning Lube Bearing Oil, but I used Rem Oil. While I didnt upgrade the bearings in this video I have done it in several other reels using Boca Ceramic Orange Seal

I’m going to try something a little different, this post will be a video post, hopefully this will work. By the way, just a warning, the video is almost 30 minutes long so it might take a few minutes to load up so please be patient. Also, if you double click the video you can view it in full screen mode.

Disclaimer: Any servicing you do to your reel you do so at your own risk and I will not be held responsible for any damage caused.

One trick I thought of after making the video is after you remove the cover take a few pictures of the internals with your digital camera. That way, in the event that parts fall out you can compare your pictures with the schematic and you should be good to go.

Well, what did you think?

Thanks for visiting my site. Be sure to tell all of your fishing buddies and come back soon

Until Next Time, Good Luck and Tight Lines To Ya!

Filed Under: Fishing Gear, Rods and Reels, Tackle Maintance Tagged With: abu revo, abu revo upgrade, carbon fiber drag, increasing drag on abu revo, increasing drag strength on revo, lube a revo, revo breakdown, revo skeet reese reel, servicing a revo, skeet reese revo, smooth drag, taking a revo apart, upgrade baitcast drag, upgrade revo drag, upgrading drag

Comments

  1. bassnman says

    October 11, 2011 at 4:34 pm

    Paul,

    It sounds to me your Revo S is just extremely dirty, then again you have had the reel for 6 years without popping the cover off, HA! Anyhow, the cover should come off with a little bit of force, just don’t overdue it.

    Have you tried running something like a think screwdriver around the edge to break up any substance that might be holding it stuck?

    You could try running warm water over it or maybe some light penetrating oil to loosen things up? If you do this then be sure to clean, dry and service the reel afterwards.

    Like I said before, be careful not to apply to much force, if you cand open it with your hands, I would NOT suggest using pliers.

    Thanks for visiting my site. Be sure to tell all of your fishing buddies and come back soon

    Until Next Time, Good Luck and Tight Lines To Ya!

    Mike

  2. Paul says

    October 11, 2011 at 3:31 pm

    Mike,

    I saw your video on servicing the Abu Garcia RevO S. I have had the reel for 6 years and this is the first time I am opening it for servicing. I unscrewed the thumb screw, twist the palm plate but it does not come loose. It seems to be stuck to the spool. I even tried wedging it loose but it is stuck pretty good. What do you think it is? Help.

    Thanks,
    Paul

TACKLE GIVEAWAY

Sign up Now

February 2025 Winner Selected!

BassnMan’s Sponsors

   
   
   
   
   

Recent Posts

  • Drop Shottting
  • Great Day Fishing
  • Weight Loss Journey, Update
  • Monthly Tackle Giveaway Update
  • Epic Fishing Day, at least at the end….
  • Restored my faith in humanity
  • Owens River Beast

Copyright © 2025 BassnMan.com[